LM224APT OverviewIn order to protect the op amps, a 14-TSSOP (0.173, 4.40mm Width) case is used. There are two types of operational amplifiers in this circuit. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 14. It consists of a total of 14 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It has 14 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~105°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.5mA and 10 . Maintain 100dB as the voltage gain. Buffer op amp is equipped with 4 channels on the device. The operating supply voltage of the buffer op amp is rated at 15V. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
LM224APT Features14 Pins
supply voltage of 5V
100dB voltage gain
LM224APT ApplicationsThere are a lot of STMicroelectronics
LM224APT Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Factory Lead Time | 12 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LM224 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Power Supplies | 5/30V |
| Number of Channels | 4 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 3V~30V ±1.5V~15V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.2μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 32V |
| Voltage - Input Offset | 2mV |
| Micropower | YES |
| Max Frequency | 100kHz |
| Bias Current-Max (IIB) @25C | 0.1μA |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.48mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM224APT Datasheet
+8613715157867