TL052CDR OverviewIn the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the J-FET-type. A Tape & Reel (TR) case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 5V battery. The op amp ic has an array of 8 pins on it. Op amp rates 3.5mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. Using an 4.8mA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 95.42dB for the time being. 2 elements make up the design of this buffer amplifier. The linear amplifier is packaged by using a TR axis.
TL052CDR Features8 Pins
supply voltage of 5V
95.42dB voltage gain
TL052CDR ApplicationsThere are a lot of Texas Instruments
TL052CDR Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Factory Lead Time | 8 Weeks |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TL052 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Power Supplies | +-5/+-15V |
| Operating Supply Current | 4.8mA |
| Nominal Supply Current | 5.6mA |
| Slew Rate | 20.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3300 kHz |
| Voltage Gain | 95.42dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 650μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 1.5mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL052CDR Datasheet
+8613715157867