TL082CDT OverviewIn order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. There are two types of operational amplifiers in this circuit. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 10mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.4mA and 10 . 106.02dB should remain the voltage gain. Buffer op amp is equipped with 2 channels on the device. The operating supply voltage of the buffer op amp is rated at 18V. As a result of this, the buffer amplifier is packed in TR.
TL082CDT Features8 Pins
supply voltage of 15V
106.02dB voltage gain
TL082CDT ApplicationsThere are a lot of STMicroelectronics
TL082CDT Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL082 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 680mW |
| Output Current | 40mA |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0004μA |
| Dual Supply Voltage | 9V |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL082CDT Datasheet
+8613715157867