OPA547FKTWT OverviewIn the package, you will find a TO-263-8, D2Pak (7 Leads + Tab), TO-263CA-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Cut Tape (CT) case is used for delivering the op amp. During the past two weeks, there have been close to 7 terminations. A total of 7 pins are located on this board. This linear amplifier should be powered by an 30V battery. The op amp ic has an array of 7 pins on it. Op amp rates 1mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Using an 10mA supply current, this operational amplifier ics can be operated. It is recommended to keep the voltage gain at 115dB at all times. On the buffer amps, there are 1 channels that can be used. The operating supply voltage of the buffer op amp is rated at 30V. The linear amplifier is packaged by using a TR axis.
OPA547FKTWT Features7 Pins
supply voltage of 30V
115dB voltage gain
OPA547FKTWT ApplicationsThere are a lot of Texas Instruments
OPA547FKTWT Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Number of Pins | 7 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Packing Method | TR |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 30V |
| Base Part Number | OPA547 |
| Pin Count | 7 |
| Operating Supply Voltage | 30V |
| Power Supplies | +-4/+-30/8/60V |
| Number of Channels | 1 |
| Operating Supply Current | 10mA |
| Nominal Supply Current | 10mA |
| Output Current | 2A |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 100nA |
| Voltage - Supply, Single/Dual (±) | 8V~60V ±4V~30V |
| Output Current per Channel | 500mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -30V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Current - Output / Channel | 750mA |
| Low-Bias | NO |
| Micropower | NO |
| Max Frequency | 1kHz |
| Bias Current-Max (IIB) @25C | 0.5μA |
| Programmable Power | YES |
| Power | YES |
| Input Offset Current-Max (IIO) | 0.05μA |
| Max Junction Temperature (Tj) | 150°C |
| Height | 4.65mm |
| Length | 10.1mm |
| Width | 8.89mm |
| Thickness | 4.44mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA547FKTWT Datasheet
+8613715157867