TLV2763IDGSR OverviewPackaged in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. The op amp is delivered to you in a Cut Tape (CT) case. There is a growing number of terminations approaching the number of 10. The pins on this board total to 10 in total. I would like to remind you that this buffer op amp should be powered by an 2.4V battery. A total of 10 pins are present on the instrumentation amplifier. There is an input offset voltage of 3.5mV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . As long as the supply current of the chip does not exceed 20μA, this op amp ic can operate. 101.58dB should remain the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. For packing the buffer amplifier, the TR-axis is adopted.
TLV2763IDGSR Features10 Pins
supply voltage of 2.4V
101.58dB voltage gain
Output Type: Rail-to-Rail
TLV2763IDGSR ApplicationsThere are a lot of Texas Instruments
TLV2763IDGSR Instrumentational OP Amps applications.
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.4V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TLV2763 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | +-0.9/+-1.8/1.8/3.6V |
| Number of Channels | 2 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 56μA |
| Power Dissipation | 485mW |
| Output Current | 10.2mA |
| Slew Rate | 0.23V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~3.6V ±0.9V~1.8V |
| Output Current per Channel | 10.2mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 500 kHz |
| Unity Gain BW-Nom | 500 kHz |
| Voltage Gain | 101.58dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 4V |
| Voltage - Input Offset | 550μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000015μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 500 kHz |
| Max I/O Voltage | 3.5mV |
| Input Offset Current-Max (IIO) | 0.000015μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| REACH SVHC | Unknown |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV2763IDGSR Datasheet
+8613715157867